The complexity of the system is such that it is broken down into sub-sections.
For a detailed description of climate control operation, refer to the relevant section of the workshop manual.
The motor and flap operation can be checked using the on-board distribution motor self-test function.
The self-test can be initiated by pressing and holding the ECON and RECIRC buttons while turning the ignition switch to the ON position.
The control module will then compare the current motor position with the values stored in the module and will indicate an error by flashing the ECON LED (light emitting diode).
If there are no errors, the LED will go out and the system will function normally.
To confirm that there are no errors, turn the ignition switch to the OFF position, then back to the ON position.
Observe the operation of the programmed defrost LED.
If there are errors present, the programmed defrost LED will flash and the system will attempt to calibrate itself.
For additional information on the function of the system, refer to the relevant section of the workshop manual.
Visual inspection
| Mechanical | Electrical |
|---|---|
|
|
Symptom chart
| Symptom | Possible causes | Action |
|---|---|---|
| No climate control function, flashing LED at start-up |
| Check the motors and levers at the heating and ventilation assembly for damage/foreign objects jamming the movement of the flaps. For additional information on the self-calibration process, see the distribution motor self-test above. |
| Poor or no cooling |
| Carry out the checks from the visual inspection, refer to the relevant section of the workshop manual. |
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer-approved diagnostic system).
| DTC | Description | Possible causes | Action |
|---|---|---|---|
| B1A5911 | Sensor 5 Volt Supply |
| Refer to the electrical guide and check the ambient air temperature sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A5913 | Sensor 5 Volt Supply |
| Refer to the electrical guide and check the ambient air temperature sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6111 | Cabin Temperature Sensor |
| Refer to the electrical guide and check the ambient air temperature sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6115 | In-Vehicle Temperature Sensor Signal |
| Refer to the electrical guide and check the ambient air temperature sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6211 | Pressure Sensor |
| Refer to the electrical guide and check the pressure sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6215 | Pressure Sensor |
| Refer to the electrical guide and check the pressure sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6312 | Right Solar Sensor |
| Refer to the electrical guides and check the right-hand sunlight sensor sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6412 | Left Solar Sensor |
| Refer to the electrical guides and check the left-hand sunlight sensor sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6713 | Sensor Ground |
| Refer to the electrical guide and check the ambient air temperature sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6811 | Ambient Temperature Sensor |
| Refer to the electrical guide and check the ambient air temperature sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6815 | Ambient Temperature Sensor |
| Refer to the electrical guides and check the ambient air temperature sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6911 | Humidity Sensor |
| Refer to the electrical guides and check the humidity/temperature sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A6915 | Humidity Sensor |
| Refer to the electrical guides and check the humidity/temperature sensor circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A7001 | Compressor Solenoid +ve Supply |
| Refer to the electrical guides and check the refrigerant solenoid circuit. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1A7111 | Air Off Temperature Sensor |
| Check the air off sensor and circuit. Refer to the electrical guides. |
| B1A7115 | Air off temperature sensor |
| Check the air off sensor and circuit. Refer to the electrical guides. |
| B1A7318 | Left Hand Seat Heater |
| Check the left-hand seat heater switch and circuit. Refer to the electrical guides. |
| B1A7418 | Right Hand Seat Heater |
| Check the right-hand seat heater switch and circuit. Refer to the electrical guides. |
| B1A9815 | LIN Bus Circuit #1 |
| Check the LIN circuits. Refer to the electrical guides. |
| B1B6013 | Feedback Potentiometer Circuit |
| Check the feedback potentiometer/air temperature mode motor circuits. Refer to the electrical guides. |
| B1B6111 | Pollution Sensor HC Input Circuit |
| Check the pollution sensor circuit. Refer to the electrical guides. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B6211 | Pollution Sensor - NOx |
| Check the pollution sensor NOx circuit. Refer to the electrical guides. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B6313 | Feedback Potentiometer Ground Circuit |
| Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B6511 | Left Hand Seat Heater Temperature Sensor |
| Check the seat heater temperature signal circuit. Refer to the electrical guides. Refer to the relevant section of the workshop manual. |
| B1B6515 | Left Hand Seat Heater Temperature Sensor |
| Check the seat heater temperature signal circuit. Refer to the electrical guides. Refer to the relevant section of the workshop manual. |
| B1B6611 | Right Hand Seat Heater Temperature Sensor |
| Check the seat heater temperature signal circuit. Refer to the electrical guides. Refer to the relevant section of the workshop manual. |
| B1B6615 | Right Hand Seat Heater Temperature Sensor |
| Check the seat heater temperature signal circuit. Refer to the electrical guides. Refer to the relevant section of the workshop manual. |
| B1B6711 | Air Intake Servo Potentiometer Circuit |
| Check the intake air motor circuit. Refer to the electrical guides. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B6715 | Air Intake Servo Potentiometer Circuit |
| Check the intake air motor circuit. Refer to the electrical guides. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B6801 | Air Intake Servo Motor |
| Check the intake air motor circuit. Refer to the electrical guides. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B7015 | LIN Bus Circuit |
| Check the LIN circuits. Refer to the electrical guides. |
| B1B7088 | LIN Bus Circuit |
| Check the LIN circuits. Refer to the electrical guides. |
| B1B7111 | Evaporator Temperature Sensor |
| Check the evaporator temperature sensor circuit. Refer to the electrical guides. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B7115 | Evaporator Temperature Sensor |
| Check the evaporator temperature sensor circuit. Refer to the electrical guides. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B7211 | LIN Bus #1 Power Supply Circuit |
| Check the LIN circuits. Refer to the electrical guides. |
| B1B7311 | LIN Bus #2 Power Supply Circuit |
| Check the LIN circuits. Refer to the electrical guides. |
| B1B7400 | Foot/Defrost Damper Actuator |
| Check for mechanical faults with the face/feet distribution motor (see visual inspection). Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B7449 | Foot/Defrost Damper Actuator |
| Check the face/feet distribution motor operation. Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B7700 | Front Right Air Blend Stepper Actuator |
| Check for the right-hand air temperature motor mechanical faults (see visual inspection). Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B7749 | Front Right Air Blend Stepper Actuator |
| Refer to the guided diagnostic routine for this code on the approved diagnostic system. |
| B1B7884 | System Pressure |
| Check the air conditioning system. Refer to the relevant section of the workshop manual. |
| B1B7885 | System Pressure |
| Check the air conditioning system and the cooling fan operation. Refer to the relevant section of the workshop manual. |
| U007388 | Control Module Communication Bus 'A' Off |
| Refer to the Network Communications section of the workshop manual. |
| U030055 | Internal Control Module Software Incompatibility |
| Configure the module using the approved diagnostic system. Check the CAN circuits. Refer to the electrical guides. |
| U1A1449 | CAN Initialization Failure |
| Configure the module using the approved diagnostic system. Check the CAN circuits. Refer to the electrical guides. |